Paradyne ACCULINK 316x User Manual Page 66
- Page / 211
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
ACCULINK 316x DSU/CSU
3-24 December 1996 3160-A2-GB22-10
Configuring the 3160/3164 DSU/CSU for
SNMP Management
To configure a 3160/3164 DSU/CSU for management
by an SNMP management system you must,
• Select and configure the port (COM or MODEM)
providing the link to the SNMP management
system.
• Set the Internet Protocol (IP) address needed to
access the device (either for the COM port or the
MODEM port).
• Select the link layer protocol (PPP or SLIP) for the
port.
• Specify the two community names that are allowed
to access the device’
s Management Information
Base (MIB).
•
Configure the device to send traps to the SNMP
manager, if desired.
Differ
ences Using the Async T
erminal: When SNMP
is
selected from the main/configuration/edit menu, the menu
selection structure changes slightly from the front panel.
Specifically, the Gen selection (from the front panel) is
split into two logical groups: System Options
and
Modem and Communication Port Options. Trap (from
the front panel) appears as Trap Options
on the async
terminal interface. (See Figures 3-14 and 3-15)
In the SNMP System Options screen as shown in
Figure 3-20, a maximum of 40 characters can be entered
per field. If more than 40 characters are required, then
scrolling on the line is supported. To scroll, move the
cursor to the end of the line. T
o clear a field, select
Clear.
This action sets the field to a null string, A message
appears requiring you to verify that a clear is intended.
After executing Clear
, the cursor is located at the
beginning of the cleared field.
Customer ID: New Cust
main/configuration/edit/snmp/system
Model: ACCULINK XXXX
System Contact:
Save Edit Main Previous Cntrl–x to Disconnect
SNMP
System Name:
System Location:
Community Name 1:
Community Name 2:
Are you sure you want to clear?
Clear
Comm.1 Access Type: _____
Clear
Comm.2 Access Type: _____
Clear
Clear
Clear
Figure 3-20. SNMP System Options Screen
Selecting the Port
The
3160/3164 DSU/CSU supports a communications
link between the DSU/CSU and an external SNMP
management system or network device (e.g., router) on
either the COM port or the MODEM port. Use the
MODEM port when configuring devices through a dial-up
modem. Use the COM port for direct connections. Either
the COM or the MODEM port can be configured as the
communications link, but only one port at a time can be
configured as the link. The MODEM port can support
either synchronous or asynchronous PPP
, or asynchronous
SLIP at data rates of up to 2400 bps. The COM port can
support either synchronous or asynchronous PPP, or
asynchronous SLIP at data rates of up to 19,200 bps.
- ACCULINK 1
- 316x DATA SERVICE UNIT/ 1
- CHANNEL SERVICE UNIT 1
- (INCLUDES TERMINAL USER 1
- INTERFACE) 1
- United States 5
- Government Requirements 7
- Table of Contents 8
- 3. Operation 9
- 4. Maintenance 9
- Appendices 9
- List of Figures 10
- List of Tables 12
- Objectives and Reader 14
- Assumptions 14
- Related Documents 14
- Reference Documents 14
- Introduction 15
- Features 16
- Physical Description 18
- 3160/3164 DSU/CSU Front Panel 18
- 3160/3164 DSU/CSU Rear Panel 18
- Table 1-1 21
- Connector Name 21
- Model 3161 DSU/CSU Rear Panel 22
- Installation 24
- SERVICES 25
- FRACTIONAL T1 26
- Box Contents 28
- Important Safety Instructions 28
- Quick Start Procedure 28
- Optional Power Selection 29
- Power-Up Self-Test 32
- Selecting a Model 3161 33
- DSU/CSU Identity 33
- Establishing Access Security 35
- Setting/Changing a Password 35
- 3160/3164 DSU/CSU Cabling 37
- Factory Default Configuration 39
- Installing Front Panel 39
- Emulation Software 39
- Enabling/Disabling the Front 40
- 3160/3164 DSU/CSU User 41
- Interface Access Security 41
- Operating the Front Panel 45
- 496-14392-0 46
- Other Displays 47
- Table 3-1 49
- System LEDs 49
- Color Meaning 49
- Table 3-2 50
- NETWORK Interface LEDs 50
- Table 3-3 51
- DSX-1 Drop/Insert Port LEDs 51
- Table 3-4 52
- Data Port LEDs 52
- Front Panel Emulation on a PC 55
- Test Jacks 56
- Configuring the DSU/CSU 58
- Configuration Procedures 59
- Saving Edit Changes 62
- Selecting a Specific Port 63
- To Copy to One or All Ports 65
- Selecting the Port 66
- Setting the IP Address 68
- Access Type(s) 71
- Configuring DS0 Channels 76
- Allocating Data Ports 84
- 496-14341a-01 91
- Selecting the Shared 94
- Communication Port 94
- Checking the Status of the 95
- Table 3-9 96
- Health and Status Messages 96
- Self-Test Health 97
- Displaying Self-Test Results 98
- Performance Report 99
- Table 3-11 100
- (2 of 2) 100
- Performance Registers 100
- Operation 101
- ACCULINK 316x DSU/CSU 102
- Controlling the DSU/CSU 103
- Interface 104
- Starting Front Panel 111
- Emulation 111
- Using the Async Terminal 112
- COM Use:Term Modem Use:Term 112
- Char Length:8 Char Length:8 112
- Dial-In:Enab 112
- Customer ID: New Cust 113
- Model: ACCULINK XXXX 113
- Enter Password: _________ 113
- Menu Selection Screens 114
- Edit and Display Screens 114
- Terminating a Session 116
- Maintenance 117
- SNMP Traps 118
- Test Commands 119
- Remote Loopback Tests 120
- Sending a V.54/ANSI FT1 121
- Activation/Deactivation 121
- Starting a Line Loopback 122
- Starting a Payload Loopback 123
- Starting a DTE Loopback 123
- Starting a Repeater Loopback 124
- DTE-initiated Loopbacks 127
- Aborting Loopbacks 127
- Sending Test Patterns 128
- Monitoring Test Patterns 129
- Aborting Test Patterns 130
- Starting a Lamp Test 130
- Aborting a Lamp Test 131
- Downloading Software 133
- Resetting the DSU/CSU 133
- Front Panel Menu A 135
- Front Panel Menu 137
- Technical Specifications 138
- Table B-1 139
- Specifications Criteria 139
- Table B-2 140
- (1 of 2) 140
- Configuration Options 142
- Context-Sensitive Menu 143
- DTE Interface Configuration 143
- Table C-1 144
- Port Configuration Options 145
- Table C-2 146
- (2 of 3) 146
- (3 of 3) 147
- Network Interface 148
- Table C-3 149
- Channel Configuration 150
- Table C-5 151
- General Configuration Options 153
- User Interface Configuration 154
- Table C-7 155
- (2 of 4) 155
- (3 of 4) 156
- (4 of 4) 157
- Alarm Configuration Options 158
- Table C-8 159
- SNMP Configuration Options 161
- Table C-9 162
- Table C-10 163
- Pin Assignments 165
- Receiver Ring 1 166
- Receiver Tip 2 166
- Transmitter Ring 4 166
- Transmitter Tip 5 166
- Receiver Ring 1 11 167
- Receiver Tip 2 3 167
- Transmitter Ring 4 9 167
- Transmitter Tip 5 1 167
- DSX-1 Port DTE Interface 168
- Integral Modem Service Port 169
- VF Ring 2 169
- VF Tip 3 169
- AUX Port Interface 170
- COM Port Interface 171
- Table D-6 172
- COM Port Connector (J6) 172
- Direction Pin Number 172
- EIA-530A DB25 Port Interface 173
- Connector 173
- RS449 Port Interface 174
- V.35 Port Interface Connector 176
- Power Cable 178
- Power Input Connector 178
- External Clock Connector 179
- Slide Latch Adapter 180
- SNMP MIB Objects 181
- Management Information Base 182
- (MIB) II (RFC 1213) 182
- (ifEntry 7) 185
- DS1/E1 MIB (RFC 1406) 187
- RS-232-like MIB (RFC 1317) 190
- Generic-Interface MIB 193
- Extensions (RFC 1229) 193
- Troubleshooting Table 195
- Table F-1 196
- Troubleshooting 196
- Configuration Worksheets 197
- Port Chan 202
- Options Value 202
- Equipment List 205
- Glossary 206
Related products and manuals for Networking Paradyne ACCULINK 316x
Networking Paradyne 8540 User Manual
(161 pages)
(161 pages)
Networking Paradyne U8777 User Manual
(182 pages)
(182 pages)
Networking Paradyne 3166 CSU User Manual
(206 pages)
(206 pages)
Networking Paradyne 8784 User Manual
(110 pages)
(110 pages)
Networking Paradyne 6218 User Manual
(78 pages)
(78 pages)
Networking Paradyne ENE2020-P User Manual
(16 pages)
(16 pages)
Networking Paradyne 7610 User Manual
(127 pages)
(127 pages)
© 2020, manymanuals.com. All rights reserved. | 0.375 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals