Paradyne IP DSLAM Multiplexer Module MUM200-2 User Manual download pdf

MUM200-2

IP DSLAM Multiplexer Module with Dual Uplink Interface Capacity

1.0 INSTALLATION

1.1 Unpack and Inspect the Multiplexer Uplink Module (MUM)

If there is visible damage, do not attempt to install the MUM200-2; contact Customer Support at 1-

877-638-2638 (001-603-427-0600 for international customers) or [email protected].

1.2 Install an Uplink Interface Module (UIM) on the MUM200-2

A UIM provides the upstream network connection, via the MUM200-2, for Net to Net Technologies' IP

DSLAMs; neither an IP DSLAM nor a MUM200-2 can function without a UIM. Any of Net to Net's

available UIM models, with the exception of the UIM-1000T and UIM-1000F, may be installed on a

MUM200-2 .

Select a port on the MUM200-2 for UIM installation; either port (1 or 2) may be used. Although

not required for operational purposes, if redundancy is desired two UIMs may be installed on a

MUM200-2, one in each port.

Remove the blanking plate from the selected port.

Carefully slide the faceplate of the UIM under the lip of the MUM200-2 faceplate at the

selected port opening such that the UIM circuit board is facedown and the label shows through

the MUM200-2 port opening with the UIM model name along the right-hand edge.

Ensure that the mounting holes on the UIM are lined up with the corresponding pems on the

MUM200-2 circuit board and that the board-to-board connector key pins are properly aligned.

Gently press down with even pressure on all four corners of the UIM until the board-to-board

connector is fully seated.

Secure the UIM circuit board to the MUM200-2 circuit board, at the pems, with the (4)

provided panhead screws.

Installation Instructions

AUTION

Net to Net Technologies strongly recommends the use of proper electrostatic discharge (ESD) precautions when

handling this equipment.

AUTION

Blanking plates should be stored for possible future use: if a UIM is removed from a

MUM200-2, it must be replaced with either another UIM or a blanking plate. DO NOT

OPERATE A MUM200-2 WITH AN OPEN UIM PORT.

220-0000069 rev 04

1 2 3 4

Summary of Contents

Page 1 - MUM200-2

MUM200-2 IP DSLAM Multiplexer Module with Dual Uplink Interface Capacity 1.0 INSTALLATION 1.1 Unpack and Inspect the Multiplexer Uplink Mod

Page 2 - 1.4.3 UIM-DS3 and UIM-E3

zSecure the UIM faceplate to the MUM200-2 faceplate using the (2) provided beige flathead screws. 1.3 Install the MUM200-2 in an IP DSLAM Chassis

Page 3 - 3.0 ADDITIONAL INFORMATION

Verify the connection: the Lnk (link) LED on the UIM-DS3 and UIM-E3 faceplate will flash green to indicate a network connection has been established.

Page 4 - 3.2.3 Europe

3.2 Regulatory Compliance for Class A Equipment The following regulatory compliance information applies to a MUM200-2 as installed in one of Net to

Comments to this Manuals

No comments

Paradyne IP DSLAM Multiplexer Module MUM200-2 User Manual

Browse online or download User Manual for Hardware Paradyne IP DSLAM Multiplexer Module MUM200-2. Paradyne IP DSLAM Multiplexer Module MUM200-2 User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Hardware Paradyne IP DSLAM Multiplexer Module MUM200-2