Paradyne FrameSaver 9783 User Manual

1FrameSaver® DSL 9783 RouterInstallation InstructionsDocument Number 9783-A2-GN11-10April 2001Contents FrameSaver DSL 9783 Router Overview ...

10Status LEDsAfter a successful self-test, the LEDs should appear as indicated in BOLD in the Condition column below.LED Condition Status System LEDs

11TroubleshootingLED Symptom ActionAll LEDs are on. If the LEDs remain on for more than ten minutes, the router is not functional. Unplug the router a

12Configuration SetupOnce the router is installed, it can be accessed locally through the menu-driven user interface via an asynchronous terminal or

13Procedure To access the menu-driven user interface:1.Verify the terminal or PC’s configuration:— Data Rate is set to 19.2 kbps.— Character Length is

14Menu NavigationThe router should operate using the default (factory-set) configuration options. Refer to the following table for help in navigating

15Verifying that Self-Test PassedTo verify that the unit passed its self-test, go to the System and Test Status screen.Main Menu → Status → System and

162.If the router will not be connected to a Paradyne DSLAM, change the DSLAM Type. Other selections are Alcatel (NewBridge), PairGain, and Nokia.3.E

17Configuring SNMP Trap Managers and TrapsProcedure To enter SNMP managers and configure traps:1.Select SNMP Traps.Main Menu → Configuration → Managem

18Procedure1.Create a DLCI on the router virtual port.Configuration → Virtual Router Ports → DLCI RecordsAssign the DLCI number that will be used for

19Verifying the End-to-End Management PathAfter installation of a remote router, run an ATM Ping test from the Hotwire® GranDSLAM.ProcedureTo Ping the

2The router has an SDSL front end and is a manageable frame relay aware endpoint. It operates as a bridge or an IP router that connects a DSL link to

20Checking PVC ConnectionsCheck PVC connections to verify that all PVCs, including management PVCs, are configured and active.Procedure To verify PVC

21Cables and ConnectorsRefer to Installing the Router on page 6 for cable installation information.The DSL network interface uses an 8-pin, un-keyed m

22The Ethernet interface connector uses an 8-pin, non-keyed modular plug. Use shielded twisted-pair CAT5, or better, cables. See Step 3 on page 7.— T

23The communication (COM) port connector uses a 25-position, EIA-232-C connector. Connecting an External ModemA standard crossover cable can be used t

24DSL Router Technical SpecificationsItem Specification*ApprovalsFCC Part 15Safety CertificationsClass A digital deviceRefer to equipment’s label for

25 Important Safety Instructions1.Read and follow all warning notices and instructions marked on the product or included in the manual.2.Slots and ope

26CE MarkingWhen the product is marked with the CE mark on the equipment label, this demonstrates full compliance with the following European Directi

27Government RequirementsCertain governments require that instructions pertaining to connection to the telephone network be included in the installati

28Warranty, Sales, Service, and Training InformationContact your local sales representative, service representative, or distributor directly for any

3Refer to About FrameSaver DSL Devices in the User’s Guide for a list of FrameSaver DSL 9783 features, and the capabilities provided by each feature s

4Wiring and Cables You May NeedThe following wiring and cables are used with this product, which uses standard interface connectors:❑Standard connect

5Prior to Installing the RouterThese Installation Instructions assume that the virtual circuits at the DSLAM have already been configured. Provisionin

6Installing the RouterPlace the FrameSaver DSL 9783 Router on a flat surface, with clearance for the rear connectors.Procedure 1.Use the supplied 8-p

73.Use an 8-pin Ethernet cable for the Ethernet connection. Insert one end of the cable into the jack labeled ETHERNET. — Use a straight-through cable

84.Use a VT100-compatible asynchronous terminal or PC to set up management access to the unit. Insert the DB25 end of the EIA-232 cable into the rout

95.Insert the supplied power cord’s round end into the jack labeled POWER. Plug the transformer into an AC outlet. Install the supplied tie wrap for s