Paradyne 4200 User Manual

GranDSLAM™ 4200ATM Stackable DSLAMUser’s GuideDocument No. 4200-A2-GB20-00August 2002

Contentsviii August 2002 4200-A2-GB20-00REPT-OPSTAT-VCL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-10Response Forma

4. DS1 Facility Commands4-8 August 2002 4200-A2-GB20-00REPT ALM T1 The REPT ALM T1 message reports current T1 (DS1) facility alarms from the NE.

4. DS1 Facility Commands4200-A2-GB20-00 August 20024-9REPT EVT T1 The REPT EVT T1 message reports current T1 (DS1) facility events from the NE. Table

4. DS1 Facility Commands4-10 August 2002 4200-A2-GB20-00REPT-OPSTAT-T1 The REPT-OPSTAT-T1 command reports current operational parameters for T1 (DS

4. DS1 Facility Commands4200-A2-GB20-00 August 20024-11Example Report DS1 facility operational parameters for NTT1-3. REPT-OPSTAT-T1:TAMPA:NTT1-1; T

4. DS1 Facility Commands4-12 August 2002 4200-A2-GB20-00RTRV-PM-T1 The RTRV-PM-T1 command retrieves DS1 performance monitoring data. Table 4-10.

4. DS1 Facility Commands4200-A2-GB20-00 August 20024-13Response Format If, in less than 2 seconds, a normal or error response cannot be sent, the foll

4. DS1 Facility Commands4-14 August 2002 4200-A2-GB20-00Example Retrieve the near-end alarm indication signal count above 4096 for a 15-minute perio

4. DS1 Facility Commands4200-A2-GB20-00 August 20024-15RTRV-T1 The RTRV-T1 command retrieves the configuration data associated with a DS-1 facility.

4. DS1 Facility Commands4-16 August 2002 4200-A2-GB20-00Normal Response: sid yy-mm-dd hh:mm:ssM c COMPLD /* RTRV-T1:[tid]:aid_ds1:[ctag]::::[p

4. DS1 Facility Commands4200-A2-GB20-00 August 20024-17 ds1_nblk(continued) TMG: Timing supply– INT: Internal timing source. Use the NE system timing

Contents4200-A2-GB20-00 August 2002ixRTRV-COND-ADSL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-28Response Format

4. DS1 Facility Commands4-18 August 2002 4200-A2-GB20-00Example Retrieve configuration data for circuit 1 on the NT. RTRV-T1:TAMPA:NTT1-1:42::::;

4200-A2-GB20-00 August 20025-15ATM CommandsOverviewThis chapter contains the following other commands:DLT-PROFILE-TRAFDSC on page 5-2DLT-VCL on page 5

5. ATM Commands5-2 August 2002 4200-A2-GB20-00DLT-PROFILE-TRAFDSC The DLT-PROFILE-TRAFDSC command deletes a selected ATM Traffic Descriptor profile

5. ATM Commands4200-A2-GB20-00 August 20025-3ExampleDelete traffic descriptor profile 5. DLT-PROFILE-TRAFDSC:TAMPA:5:42; TAMPA 01-11-24 12:30:43M 4

5. ATM Commands5-4 August 2002 4200-A2-GB20-00DLT-VCL The DLT-VCL command deletes selected ATM interface Virtual Channel Links (VCL) that are not i

5. ATM Commands4200-A2-GB20-00 August 20025-5Error Response: sid yy-mm-dd hh:mm:ssM c DENY /* DLT-VCL:[tid]:aid_vcl:[ctag][:] */ aid:ERRCDE=e

5. ATM Commands5-6 August 2002 4200-A2-GB20-00ED-ATMPORT The ED-ATMPORT command edits configuration data associated with an ATM port in the NE. Res

5. ATM Commands4200-A2-GB20-00 August 20025-7Example Edit rack 1, shelf 1, slot 1, circuit 9 to have an OAM segment location ID of all ones. ED-ATMPOR

5. ATM Commands5-8 August 2002 4200-A2-GB20-00ENT-PROFILE-TRAFDSC The ENT-PROFILE-TRAFDSC command creates a new ATM Traffic Descriptor profile. Re

5. ATM Commands4200-A2-GB20-00 August 20025-9Error Response: sid yy-mm-dd hh:mm:ssM c DENY /* ENT-PROFILE-TRAFDSC:[tid]:trafdsc:[ctag]::trafdsc

Contentsx August 2002 4200-A2-GB20-00ED-PID. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-6Respo

5. ATM Commands5-10 August 2002 4200-A2-GB20-00ENT-VCL The ENT-VCL command creates an ATM interface Virtual Channel Links (VCL) on an NT or LT. Ta

5. ATM Commands4200-A2-GB20-00 August 20025-11Response Format If, in less than 2 seconds, a normal or error response cannot be sent, the following ack

5. ATM Commands5-12 August 2002 4200-A2-GB20-00 Example Create a VCL for Virtual Path 15, Virtual Channel 207 with a Receive Traffic Descriptor of 1

5. ATM Commands4200-A2-GB20-00 August 20025-13RTRV-ATMPORT The RTRV-ATMPORT command retrieves configuration data associated with an ATM port in the

5. ATM Commands5-14 August 2002 4200-A2-GB20-00Error Response: sid yy-mm-dd hh:mm:ssM c DENY /* RTRV-ATMPORT:[tid]:aid_atmport:[ctag]::::[pst

5. ATM Commands4200-A2-GB20-00 August 20025-15Example Retrieve parameters for in-service entities in the loopback state on the NTATM port. RTRV-ATMPOR

5. ATM Commands5-16 August 2002 4200-A2-GB20-00RTRV-PROFILE-ATMACC The RTRV-PROFILE-ATMACC command retrieves configuration parameters of an ATM acc

5. ATM Commands4200-A2-GB20-00 August 20025-17Table 5-14. RTRV-ATMACC Response ParametersParameter Explanation tid Target NE identification yy-mm-dd

5. ATM Commands5-18 August 2002 4200-A2-GB20-00Example Retrieve parameters for profile 6. RTRV-PROFILE-ATMACC:TAMPA:6:42::,LOCAL; TAMPA 01-11-24 1

5. ATM Commands4200-A2-GB20-00 August 20025-19RTRV-PROFILE-TRAFDSC The RTRV-PROFILE-TRAFDSC command retrieves configuration parameters of an ATM traf

Contents4200-A2-GB20-00 August 2002xi14 System CommandsOverview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5. ATM Commands5-20 August 2002 4200-A2-GB20-00Example Retrieve parameters for profile 6. RTRV-PROFILE-TRAFDSC:TAMPA:6:42::; TAMPA 01-11-24 12:30:

5. ATM Commands4200-A2-GB20-00 August 20025-21RTRV-VCL The RTRV-VCL command retrieves configuration data associated with an ATM virtual channel link.

5. ATM Commands5-22 August 2002 4200-A2-GB20-00Normal Response: sid yy-mm-dd hh:mm:ssM c COMPLD /* RTRV-VCL:[tid]:aid_vci:[ctag]::::[pstf][sst

5. ATM Commands4200-A2-GB20-00 August 20025-23Example Retrieve VCL for virtual path 15, virtual channel 307. RTRV-VCL:TAMPA:NTVCL-15-307:42; TAMPA 0

5. ATM Commands5-24 August 2002 4200-A2-GB20-00

4200-A2-GB20-00 August 20026-16Cross Connect CommandsOverviewThis chapter contains the following CrossConnect commands:DLT-CRS-VC on page 6-2ED-CRS-VC

6. Cross Connect Commands6-2 August 2002 4200-A2-GB20-00DLT-CRS-VC The DLT-CRS-VC command deletes selected VC-level cross-connections between the N

6. Cross Connect Commands4200-A2-GB20-00 August 20026-3Normal Response: sid yy-mm-dd hh:mm:ssM c COMPLD /* DLT-CRS-VC:[tid]:nt_vcl,lt_vcl:[ctag]

6. Cross Connect Commands6-4 August 2002 4200-A2-GB20-00ED-CRS-VC The ED-CRS-VC command edits the configuration of a VC-level cross-connection betw

6. Cross Connect Commands4200-A2-GB20-00 August 20026-5Response Format If, in less than 2 seconds, a normal or error response cannot be sent, the foll

Contentsxii August 2002 4200-A2-GB20-00RTRV-META-CMD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-21Response Form

6. Cross Connect Commands6-6 August 2002 4200-A2-GB20-00Example Edit VC-level cross-connection between Virtual Path 14, Virtual Channel 307 (network

6. Cross Connect Commands4200-A2-GB20-00 August 20026-7ENT-CRS-VC The ENT-CRS-VC command establishes a VC-level cross-connection between the NT and L

6. Cross Connect Commands6-8 August 2002 4200-A2-GB20-00Response Format If, in less than 2 seconds, a normal or error response cannot be sent, the f

6. Cross Connect Commands4200-A2-GB20-00 August 20026-9Example Establish a VC-level cross-connection between Virtual Path 14, Virtual Channel 307 (net

6. Cross Connect Commands6-10 August 2002 4200-A2-GB20-00RTRV-CRS-VC The RTRV-CRS-VC command retrieves the configuration of an ATM Interface Virtua

6. Cross Connect Commands4200-A2-GB20-00 August 20026-11Response Format If, in less than 2 seconds, a normal or error response cannot be sent, the fol

6. Cross Connect Commands6-12 August 2002 4200-A2-GB20-00Example Retrieve configuration for the In-Service VC-level cross-connection involving Virtu

4200-A2-GB20-00 August 20027-17Equipment CommandsOverviewThis chapter contains the following Equipment commands:ED-EQPT on page 7-2REPT ALM EQPT on pa

7. Equipment Commands7-2 August 2002 4200-A2-GB20-00ED-EQPT The ED-EQPT command edits configuration data associated with equipment supported by th

7. Equipment Commands4200-A2-GB20-00 August 20027-3Error Response: sid yy-mm-dd hh:mm:ssM c DENY /* ED-EQPT:[tid]:aid_eqpts:[ctag]::[eqpt_nblk]

Contents4200-A2-GB20-00 August 2002xiiiRLS-LPBK-VCL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15-9Response F

7. Equipment Commands7-4 August 2002 4200-A2-GB20-00REPT ALM EQPT The REPT ALM EQPT message reports current alarms from the NE. Table 7-3. REPT ALM

7. Equipment Commands4200-A2-GB20-00 August 20027-5REPT EVT EQPT The REPT EVT EQPT message reports current equipment events from the NE. Table 7-4. R

7. Equipment Commands7-6 August 2002 4200-A2-GB20-00RTRV-EQPT The RTRV-EQPT command retrieves configuration data associated with a unit of equipmen

7. Equipment Commands4200-A2-GB20-00 August 20027-7Error Response: sid yy-mm-dd hh:mm:ssM c DENY /* RTRV-EQPT:[tid]:aid_eqpts:[ctag] */ aid:E

7. Equipment Commands7-8 August 2002 4200-A2-GB20-00Example Retrieve configuration data associated with Shelf 1. RTRV-EQPT:TAMPA:SHELF-1-1:42; TAM

7. Equipment Commands4200-A2-GB20-00 August 20027-9RTRV-INV-EQPT The RTRV-INV-EQPT command retrieves inventory data associated with a unit of equipme

7. Equipment Commands7-10 August 2002 4200-A2-GB20-00Error Response: sid yy-mm-dd hh:mm:ssM c DENY /* RTRV-INV-EQPT:[tid]:aid_eqpts:[ctag] */

7. Equipment Commands4200-A2-GB20-00 August 20027-11Example Retrieve inventory for Shelf 1. RTRV-INV-EQPT:TAMPA:SHELF-1-1:42::; TAMPA 02-08-06 12:30

7. Equipment Commands7-12 August 2002 4200-A2-GB20-00

4200-A2-GB20-00 August 20028-18IP Access CommandsOverviewThis chapter contains the following IP Access commands:DLT-ATMARPENT on page 8-2DLT-IPPORT on

Contentsxiv August 2002 4200-A2-GB20-00C Traps and MIBsSNMP Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8. IP Access Commands8-2 August 2002 4200-A2-GB20-00DLT-ATMARPENT The command DLT-ATMARPENT deletes entries in the ATM Address Resolution Protocol

8. IP Access Commands4200-A2-GB20-00 August 20028-3Example Delete the entry for ATM-2 port with IP address 123.201.143.71. DLT-ATMARPENT:TAMPA:ATM-2:4

8. IP Access Commands8-4 August 2002 4200-A2-GB20-00DLT-IPPORT The command DLT-IPPORT deletes an Internet Protocol port (or interface) in the NE. A

8. IP Access Commands4200-A2-GB20-00 August 20028-5Example Delete ATM-2 port. DLT-IPPORT:TAMPA:ATM-2:42; TAMPA 01-11-24 12:30:43M 42 COMPLD /* DL

8. IP Access Commands8-6 August 2002 4200-A2-GB20-00ED-IPPORT The command ED-IPPORT edits configuration data associated with an Internet Protocol

8. IP Access Commands4200-A2-GB20-00 August 20028-7Response Format If, in less than 2 seconds, a normal or error response cannot be sent, the followin

8. IP Access Commands8-8 August 2002 4200-A2-GB20-00Example Configure the SLIP port with a configuration mode of BOOTP and a physical address of 18-

8. IP Access Commands4200-A2-GB20-00 August 20028-9ENT-ATMARPENT The command ENT-ATMARPENT defines a new entry in the ATM Address Resolution Protocol

8. IP Access Commands8-10 August 2002 4200-A2-GB20-00Error Response: sid yy-mm-dd hh:mm:ssM c DENY; /* ENT-ATMARPENT:[tid]:aid_ipport:[ctag]:

8. IP Access Commands4200-A2-GB20-00 August 20028-11ENT-IPPORT The command ENT-IPPORT configures an Internet Protocol port (or interface) in the NE.

Contents4200-A2-GB20-00 August 2002xvParadyne ReachDSL MIB (pdn_reachDSL.mib) . . . . . . . . . . . . . . . . . C-45Paradyne DS1 Config MIB (RFC 2495)

8. IP Access Commands8-12 August 2002 4200-A2-GB20-00Response Format If, in less than 2 seconds, a normal or error response cannot be sent, the foll

8. IP Access Commands4200-A2-GB20-00 August 20028-13Example Configure the SLIP port with a configuration mode of BOOTP and a physical address of 18-00

8. IP Access Commands8-14 August 2002 4200-A2-GB20-00REPT-OPSTAT-IPPORT The command REPT-OPSTAT-IPPORT reports current operational parameters for

8. IP Access Commands4200-A2-GB20-00 August 20028-15Table 8-12. REPT-OPSTAT-IPPORT Response ParametersParameter Explanation tid Target NE identificati

8. IP Access Commands8-16 August 2002 4200-A2-GB20-00Example Report IP port facility parameters for ETH-1. REPT-OPSTAT-IPPORT:TAMPA:ETH-1 TAMPA 01

8. IP Access Commands4200-A2-GB20-00 August 20028-17RTRV-ATMARPENT The command RTRV-ATMARPENT retrieves entries in the ATM Address Resolution Protoco

8. IP Access Commands8-18 August 2002 4200-A2-GB20-00Example Retrieve the entry for ATM-2 port with IP address 123.201.143.71. RTRV-ATMARPENT:TAMPA:

8. IP Access Commands4200-A2-GB20-00 August 20028-19RTRV-IPPORT The RTRV-IPPORT command retrieves configuration data associated with an Internet Pr

8. IP Access Commands8-20 August 2002 4200-A2-GB20-00Error Response: sid yy-mm-dd hh:mm:ssM c DENY; /* RTRV-IPPORT:[tid]:aid_ipport:[ctag][:]

8. IP Access Commands4200-A2-GB20-00 August 20028-21Example Retrieve the configuration data associated with the ATM-1 port. RTRV-IPPORT:TAMPA:ATM-1:42

Contentsxvi August 2002 4200-A2-GB20-00

8. IP Access Commands8-22 August 2002 4200-A2-GB20-00

4200-A2-GB20-00 August 20029-19Performance CommandsOverviewThis chapter contains the following Performance commands:REPT-OPSTAT-ADSLCOM on page 9-2REP

9. Performance Commands9-2 August 2002 4200-A2-GB20-00REPT-OPSTAT-ADSLCOM The REPT-OPSTAT-ADSLCOM command reports current operational parameters of

9. Performance Commands4200-A2-GB20-00 August 20029-3Table 9-2. REPT-OPSTAT-ADSLCOM Response ParametersParameter Explanation tid Target NE identificat

9. Performance Commands9-4 August 2002 4200-A2-GB20-00Examples Report ADSL DMT carrier operations parameters for ADSL-1-1-1-3. REPT-OPSTAT-ADSLCOM:T

9. Performance Commands4200-A2-GB20-00 August 20029-5REPT-OPSTAT-ADSLDN The REPT-OPSTAT-ADSLDN command reports operational parameters of ADSL lines i

9. Performance Commands9-6 August 2002 4200-A2-GB20-00Example Report downstream operations parameters for ADSL-1-1-1-3. REPT-OPSTAT-ADSLDN:TAMPA:ADS

9. Performance Commands4200-A2-GB20-00 August 20029-7REPT-OPSTAT-ADSLUP The REPT-OPSTAT-ADSLUP command reports operational parameters of ADSL lines i

9. Performance Commands9-8 August 2002 4200-A2-GB20-00Table 9-6. REPT-OPSTAT-ADSLUP Response ParametersParameter Explanation tid Target NE identific

9. Performance Commands4200-A2-GB20-00 August 20029-9Example Report upstream operations parameters for ADSL-1-1-1-3. REPT-OPSTAT-ADSLUP:TAMPA:ADSL-1-1

4200-A2-GB20-00 August 2002xviiAbout This GuideDocument Purpose and Intended AudienceThis guide contains information necessary for the use of the Gran

9. Performance Commands9-10 August 2002 4200-A2-GB20-00REPT-OPSTAT-VCL The REPT-OPSTAT-VCL command reports operational parameters for a Virtual Cha

9. Performance Commands4200-A2-GB20-00 August 20029-11Table 9-8. REPT-OPSTAT-VCL Response ParametersParameter Explanation tid Target NE identification

9. Performance Commands9-12 August 2002 4200-A2-GB20-00Example Report VCL operations parameters for NTVCL-0-32. REPT-OPSTAT-VCL:NTVCL-0-32; TAMPA

4200-A2-GB20-00 August 200210-110Fault CommandsOverviewThis chapter contains the following Fault commands:RTRV-ALM-ADSL on page 10-2RTRV-ALM-ALL on pa

10. Fault Commands10-2 August 2002 4200-A2-GB20-00RTRV-ALM-ADSL The RTRV-ALM-ADSL command retrieves current alarms associated with an ADSL facilit

10. Fault Commands4200-A2-GB20-00 August 200210-3Response Format If, in less than 2 seconds, a normal or error response cannot be sent, the following

10. Fault Commands10-4 August 2002 4200-A2-GB20-00Example Retrieve all major service-affecting ADSL alarms for rack 1, shelf 1, slot 1, circuit 4. R

10. Fault Commands4200-A2-GB20-00 August 200210-5RTRV-ALM-ALL The RTRV-ALM-ALL command retrieves current alarms in the NE. Table 10-3. RTRV-ALM-ALL

10. Fault Commands10-6 August 2002 4200-A2-GB20-00Response Format If, in less than 2 seconds, a normal or error response cannot be sent, the followi

10. Fault Commands4200-A2-GB20-00 August 200210-7ntfncde As described for command parameters (see Table 10-3, RTRV-ALM-ALL Command Parameters), excep

A August 2002 4200-A2-GB20-00Copyright © 2002 Paradyne Corporation.All rights reserved.Printed in U.S.A.NoticeThis publication is protected by federal

About This Guidexviii August 2002 4200-A2-GB20-00A master glossary of terms and acronyms used in Paradyne documents is available online at www.paradyn

10. Fault Commands10-8 August 2002 4200-A2-GB20-00Example Retrieve all active, critical, service-affecting the TAMPA NE.RTRV-ALM-ALL:TAMPA:ALL:42::C

10. Fault Commands4200-A2-GB20-00 August 200210-9RTRV-ALM-EQPT The RTRV-ALM-EQPT command retrieves current alarms for specified equipment. Table 10

10. Fault Commands10-10 August 2002 4200-A2-GB20-00Response Format If, in less than 2 seconds, a normal or error response cannot be sent, the follow

10. Fault Commands4200-A2-GB20-00 August 200210-11Example Retrieve all service-affecting critical alarms for Network Termination Unit B. RTRV-ALM-EQPT

10. Fault Commands10-12 August 2002 4200-A2-GB20-00RTRV-ALM-T1 The RTRV-ALM-T1 command retrieves current alarms for selected DS1 facilities. Tabl

10. Fault Commands4200-A2-GB20-00 August 200210-13Response Format If, in less than 2 seconds, a normal or error response cannot be sent, the following

10. Fault Commands10-14 August 2002 4200-A2-GB20-00Example Retrieve service-affecting critical alarms for NTT-1. RTRV-ALM-T1:TAMPA:NTT-1:42::CR,,SA;

10. Fault Commands4200-A2-GB20-00 August 200210-15RTRV-ATTR-ADSL The RTRV-ATTR-ADSL command retrieves current attributes of activities related to t

10. Fault Commands10-16 August 2002 4200-A2-GB20-00Response Format If, in less than 2 seconds, a normal or error response cannot be sent, the follow

10. Fault Commands4200-A2-GB20-00 August 200210-17Example Retrieve major attributes for all ADSL facilities. RTRV-ATTR-ADSL:TAMPA:ADSL:42::MJ; TAMPA

About This Guide4200-A2-GB20-00 August 2002xixTo order a paper copy of a Paradyne document:Within the U.S.A., call 1-800-PARADYNE (1-800-727-2396)Outs

10. Fault Commands10-18 August 2002 4200-A2-GB20-00RTRV-ATTR-ALL The RTRV-ATTR-ALL command retrieves current attributes of all conditions maintai

10. Fault Commands4200-A2-GB20-00 August 200210-19Response Format If, in less than 2 seconds, a normal or error response cannot be sent, the following

10. Fault Commands10-20 August 2002 4200-A2-GB20-00Error Response: sid yy-mm-dd hh:mm:ssM c DENY /* RTRV-ATTR-ALL:[tid]:aid_all:[ctag]::[ntfn

10. Fault Commands4200-A2-GB20-00 August 200210-21Example Retrieve current attributes for all major conditions maintained by the TAMPA NE. RTRV-ATTR-

10. Fault Commands10-22 August 2002 4200-A2-GB20-00RTRV-ATTR-EQPT The RTRV-ATTR-EQPT command retrieves current attributes of activities related to

10. Fault Commands4200-A2-GB20-00 August 200210-23Response Format If, in less than 2 seconds, a normal or error response cannot be sent, the following

10. Fault Commands10-24 August 2002 4200-A2-GB20-00Example Retrieve service-affecting critical alarms for equipment. RTRV-ATTR-EQPT:TAMPA:EQPT:42::M

10. Fault Commands4200-A2-GB20-00 August 200210-25RTRV-ATTR-T1 The RTRV-ATTR-T1 command retrieves current attributes of activities related to the DS

10. Fault Commands10-26 August 2002 4200-A2-GB20-00Response Format If, in less than 2 seconds, a normal or error response cannot be sent, the follow

10. Fault Commands4200-A2-GB20-00 August 200210-27Example Retrieve critical attributes for T1 conditions. RTRV-ATTR-T1:TAMPA:T1:42::CR; TAMPA 02-04-

About This Guidexx August 2002 4200-A2-GB20-00

10. Fault Commands10-28 August 2002 4200-A2-GB20-00RTRV-COND-ADSL The RTRV-COND-ADSL command retrieves the current condition of selected ADSL line

10. Fault Commands4200-A2-GB20-00 August 200210-29Response Format If, in less than 2 seconds, a normal or error response cannot be sent, the following

10. Fault Commands10-30 August 2002 4200-A2-GB20-00Example Retrieve near-end loss-of-signal condition of ADSL line for rack 1, shelf 1, slot 1, circ

10. Fault Commands4200-A2-GB20-00 August 200210-31RTRV-COND-ALL The RTRV-COND-ALL command retrieves the condition of NE alarm indicators. Table 10-1

10. Fault Commands10-32 August 2002 4200-A2-GB20-00Response Format If, in less than 2 seconds, a normal or error response cannot be sent, the follow

10. Fault Commands4200-A2-GB20-00 August 200210-33DENY Input command is denied /* */ Enclosed are human readable comments – unspecified format errcd

10. Fault Commands10-34 August 2002 4200-A2-GB20-00Example Retrieve current attributes for all near-end conditions maintained by the TAMPA NE. RTRV

10. Fault Commands4200-A2-GB20-00 August 200210-35RTRV-COND-EQPT The RTRV-COND-EQPT command retrieves the current condition of specified equipment a

10. Fault Commands10-36 August 2002 4200-A2-GB20-00Response Format If, in less than 2 seconds, a normal or error response cannot be sent, the follow

10. Fault Commands4200-A2-GB20-00 August 200210-37Example Retrieve current condition of LT alarm indicators. RTRV-COND-EQPT:TAMPA:LT:42::; TAMPA 02-

4200-A2-GB20-00 August 20021-11Introduction to the Hotwire 4200 GranDSLAMOverviewThe GranDSLAM™ 4200 ATM Stackable DSLAM is a stackable DSLAM designed

10. Fault Commands10-38 August 2002 4200-A2-GB20-00RTRV-COND-T1 The RTRV-COND-T1 command retrieves current conditions of a DS1 facility. Table 10-

10. Fault Commands4200-A2-GB20-00 August 200210-39Response Format If, in less than 2 seconds, a normal or error response cannot be sent, the following

10. Fault Commands10-40 August 2002 4200-A2-GB20-00Example Retrieve current conditions for NTT1 facility. RTRV-COND-T1:TAMPA:NTT1:42::,; TAMPA 02-

4200-A2-GB20-00 August 200211-111Log CommandsOverviewThis chapter contains the following Log commands:INIT-LOG on page 11-2RTRV-LOG on page 11-4

11. Log Commands11-2 August 2002 4200-A2-GB20-00INIT-LOG The INIT-LOG command initializes selected logs. Response Format If, in less than 2 second

11. Log Commands4200-A2-GB20-00 August 200211-3Example Initialize the SYSTEM log. INIT-LOG:TAMPA::40::SYSTEM; TAMPA 02-07-24 10:30:43M 40 COMPLD

11. Log Commands11-4 August 2002 4200-A2-GB20-00RTRV-LOG The RTRV-LOG command retrieves selected logs. Response Format If, in less than 2 seconds

11. Log Commands4200-A2-GB20-00 August 200211-5Example Retrieve the SECURITY log. RTRV-LOG:TAMPA::40::SECURITY; TAMPA 02-07-24 10:30:43M 40 COMPLD

11. Log Commands11-6 August 2002 4200-A2-GB20-00

4200-A2-GB20-00 August 200212-112Security CommandsOverviewThis chapter contains the following Security commands:DLT-USER-SECU on page 12-2ED-CID-SECU

1. Introduction to the Hotwire 4200 GranDSLAM1-2 August 2002 4200-A2-GB20-00Figure 1-2 shows a typical application for the GranDSLAM 4200.Figure 1-2

12. Security Commands12-2 August 2002 4200-A2-GB20-00DLT-USER-SECU The DLT-USER-SECU command deletes a user account from the NE database. Response

12. Security Commands4200-A2-GB20-00 August 200212-3Example Delete user RICHARD. DLT-USER-SECU:TAMPA:RICHARD:42; TAMPA 01-11-24 12:30:43M 42 COMPLD

12. Security Commands12-4 August 2002 4200-A2-GB20-00ED-CID-SECU The ED-CID-SECU command edits the configuration data associated with the Channel I

12. Security Commands4200-A2-GB20-00 August 200212-5Normal Response: sid yy-mm-dd hh:mm:ssM c COMPLD /*ED-CID-SECU:[tid]:cid:[ctag]::chap,:[cid_

12. Security Commands12-6 August 2002 4200-A2-GB20-00ED-PID The ED-PID command edits a user’s own Private Identifier (password). Response Format If,

12. Security Commands4200-A2-GB20-00 August 200212-7Example Change Richard’s password from RCC-1210D to NR-12345. ED-PID:TAMPA:RICHARD:42::RCC-1210D,N

12. Security Commands12-8 August 2002 4200-A2-GB20-00ED-USER-SECU The ED-USER-SECU command edits the security levels and other security-related par

12. Security Commands4200-A2-GB20-00 August 200212-9Normal Response: sid yy-mm-dd hh:mm:ssM c COMPLD/*ED-USER-SECU:[tid]:uid:[ctag]::[newid],[newpid]

12. Security Commands12-10 August 2002 4200-A2-GB20-00ENT-USER-SECU The ENT-USER-SECU command defines the security levels and other security-relate

12. Security Commands4200-A2-GB20-00 August 200212-11Error Response: sid yy-mm-dd hh:mm:ssM c DENY /* ENT-USER-SECU:[tid]:uid:[ctag]::pid,,[uap

1. Introduction to the Hotwire 4200 GranDSLAM4200-A2-GB20-00 August 20021-3FeaturesThe GranDSLAM 4200 DSLAM has the following features:Compact size (h

12. Security Commands12-12 August 2002 4200-A2-GB20-00RTRV-CID-SECU The RTRV-CID-SECU command retrieves the configuration data associated with the

12. Security Commands4200-A2-GB20-00 August 200212-13Example Retrieve the configuration data for the local console interface. RTRV-CID-SECU:TAMPA:CRAF

12. Security Commands12-14 August 2002 4200-A2-GB20-00RTRV-USER-SECU The RTRV-USER-SECU command retrieves the security levels for a specified user.

12. Security Commands4200-A2-GB20-00 August 200212-15Example Retrieve the security levels for user RICHARD. RTRV-USER-SECU:TAMPA:RICHARD:42; TAMPA 0

12. Security Commands12-16 August 2002 4200-A2-GB20-00

4200-A2-GB20-00 August 200213-113Synchronization CommandsOverviewThis chapter contains the following Synchronization commands:ED-SYNCN on page 13-2RD-

13. Synchronization Commands13-2 August 2002 4200-A2-GB20-00ED-SYNCN The ED-SYNCN Command configures the reference source for synchronization of

13. Synchronization Commands4200-A2-GB20-00 August 200213-3Example Configure the NE clock to use the local oscillator as its primary reference source.

13. Synchronization Commands13-4 August 2002 4200-A2-GB20-00RD-SYNCN The RD-SYNCN Command retrieves the current reference source for synchronizat

13. Synchronization Commands4200-A2-GB20-00 August 200213-5Example Retrieve the NE clock source. RD-SYNCN:TAMPA:CLKSRCNT:42; TAMPA 01-12-20 11:20:34

1. Introduction to the Hotwire 4200 GranDSLAM1-4 August 2002 4200-A2-GB20-00

13. Synchronization Commands13-6 August 2002 4200-A2-GB20-00RTRV-SYNCN The RTRV-SYNCN Command retrieves the configuration of the reference source

13. Synchronization Commands4200-A2-GB20-00 August 200213-7Example Retrieve the configuration of the reference source for synchronization of the NE cl

13. Synchronization Commands13-8 August 2002 4200-A2-GB20-00

4200-A2-GB20-00 August 200214-114System CommandsOverviewThis chapter contains the following System commands:ACT-USER on page 14-2ALW-MSG-ALL on page 1

14. System Commands14-2 August 2002 4200-A2-GB20-00ACT-USER The ACT-USER command logs a user on and begins a user session. Response Format If, in

14. System Commands4200-A2-GB20-00 August 200214-3Example Activate JANET, whose password is ABC-1234. ACT-USER:TAMPA:JANET:1::ABC-1234; TAMPA 01-10-

14. System Commands14-4 August 2002 4200-A2-GB20-00ALW-MSG-ALL The ALW-MSG-ALL command allows all autonomous messages to be reported. This command

14. System Commands4200-A2-GB20-00 August 200214-5Example Enable the autonomous messages to be reported in the OS. ALW-MSG-ALL:TAMPA:ALL:40::MN; TA

14. System Commands14-6 August 2002 4200-A2-GB20-00CANC-USER The CANC-USER command logs off a user’s own session. Response Format If, in less than

14. System Commands4200-A2-GB20-00 August 200214-7Example Cancel the user ID JANET. CANC-USER:TAMPA:JANET:40; TAMPA 01-10-25 10:35:34M 40 COMPLD

4200-A2-GB20-00 August 20022-12Using the Command Line InterfaceOverviewThe Command Line Interface (CLI) is accessible via either a directly connected

14. System Commands14-8 August 2002 4200-A2-GB20-00CPY-FILE The CPY-FILE command copies the contents of a configuration or software file on a select

14. System Commands4200-A2-GB20-00 August 200214-9INH-MSG-ALL The INH-MSG-ALL command inhibits the reporting of all autonomous messages at or below

14. System Commands14-10 August 2002 4200-A2-GB20-00Example Inhibit the reporting of Minor and Not Alarmed autonomous messages. INH-MSG-ALL:TAMPA:AL

14. System Commands4200-A2-GB20-00 August 200214-11INIT-SYS The INIT-SYS command initializes or resets selected subsystems in the NE. Response Forma

14. System Commands14-12 August 2002 4200-A2-GB20-00Example Perform a complete reset of the NTA unit. INIT-SYS:TAMPA:NTA:40::3; TAMPA 02-03-22 10:

14. System Commands4200-A2-GB20-00 August 200214-13LOGOFF The LOGOFF command logs the invoking terminal session. Response Format If, in less than 2

14. System Commands14-14 August 2002 4200-A2-GB20-00Example Log off the TAMPA NE. LOGOFF:TAMPA::40; TAMPA 01-10-25 10:35:34M 40 COMPLD /* LOGOF

14. System Commands4200-A2-GB20-00 August 200214-15RTRV-HDR The RTRV-HDR command retrieves the NE header information. Response Format If, in less t

14. System Commands14-16 August 2002 4200-A2-GB20-00Example Retrieve header information for the TAMPA NE. RTRV-HDR:TAMPA::42; TAMPA 01-10-24 11:30

14. System Commands4200-A2-GB20-00 August 200214-17RTRV-MEM The RTRV-MEM command retrieves a list of software image files available in the NE, along

2. Using the Command Line Interface2-2 August 2002 4200-A2-GB20-00Command Code The command code consists of a verb and one or more modifiers. Table

14. System Commands14-18 August 2002 4200-A2-GB20-00Example Retrieve the list of software image files for the TAMPA NE. RTRV-MEM:TAMPA:COM:40; TAM

14. System Commands4200-A2-GB20-00 August 200214-19RTRV-META-AID The RTRV-META-AID command retrieves the Access Identification (AID) of a specific co

14. System Commands14-20 August 2002 4200-A2-GB20-00Example Retrieve the AID for the RTRV-IPPORT command. RTRV-META-AID:TAMPA:IPPORT:40; TAMPA 02-

14. System Commands4200-A2-GB20-00 August 200214-21RTRV-META-CMD The RTRV-META-CMD command retrieves a specific or a list of all TL1 commands. Respon

14. System Commands14-22 August 2002 4200-A2-GB20-00Example Retrieve the RTRV-IPPORT command. RTRV-META-CMD:TAMPA:RTRV-IPPORT:40; TAMPA 02-07-24 1

14. System Commands4200-A2-GB20-00 August 200214-23RTRV-META-SYN The RTRV-META-SYN command retrieves the syntax of a specific command or the syntax o

14. System Commands14-24 August 2002 4200-A2-GB20-00Example Retrieve the syntax for the RTRV-IPPORT command. RTRV-META-SYN:TAMPA:RTRV-IPPORT:40; T

14. System Commands4200-A2-GB20-00 August 200214-25RTRV-NE-ALL The RTRV-NE-ALL command retrieves common configuration data associated with the NE. Re

14. System Commands14-26 August 2002 4200-A2-GB20-00Table 14-22. RTRV-NE-ALL Response Parameters (1 of 3)Parameter Explanation sid Source NE identif

14. System Commands4200-A2-GB20-00 August 200214-27ne_nblk (continued)SNTPIPADDR: Simple Network Timing Protocol Server IP Address. Specifies the IP a

2. Using the Command Line Interface4200-A2-GB20-00 August 20022-3Parameters Parameters are values which clarify the function of a command. Parameter s

14. System Commands14-28 August 2002 4200-A2-GB20-00Example Retrieve the common configuration data associated with the TAMPA NE. RTRV-NE-ALL:TAMPA:C

14. System Commands4200-A2-GB20-00 August 200214-29 SET-DAT The SET-DAT command sets the date and time in an NE. Response Format If, in less than 2

14. System Commands14-30 August 2002 4200-A2-GB20-00Example Set the date to 20 October 2001 and the time to 11:13:35 in the TAMPA NE. SET-DAT:TAMPA:

14. System Commands4200-A2-GB20-00 August 200214-31SET-NE-ALL The SET-NE-ALL command sets common configuration parameters associated with the NE. Tab

14. System Commands14-32 August 2002 4200-A2-GB20-00ne_nblk RMTSYSLOG: Remote syslog. Enables or disables syslog messages to a remote daemon. The de

14. System Commands4200-A2-GB20-00 August 200214-33Response Format If, in less than 2 seconds, a normal or error response cannot be sent, the followin

14. System Commands14-34 August 2002 4200-A2-GB20-00Example Retrieve the common configuration parameters associated with the TAMPA NE. SET-NE-ALL:TA

14. System Commands4200-A2-GB20-00 August 200214-35SET-SID The SET-SID command sets the system identifier (SID) of a network element. Response Forma

14. System Commands14-36 August 2002 4200-A2-GB20-00Example Set the SID for the TAMPA NE to "TAMPA-FL". SET-SID:TAMPA::42::TAMPA-FL; TAM

4200-A2-GB20-00 August 200215-115Test CommandsOverviewThis chapter contains the following Test commands:OPR-LPBK-T1 on page 15-2OPR-LPBK-VCL on page 1

4200-A2-GB20-00 August 2002iContentsAbout This GuideDocument Purpose and Intended Audience . . . . . . . . . . . . . . . . . . . . xviiDocument Summa

2. Using the Command Line Interface2-4 August 2002 4200-A2-GB20-00Command Entry FeaturesThe GranDSLAM 4200 uses Transaction Language No. 1 (TL1) lan

15. Test Commands15-2 August 2002 4200-A2-GB20-00OPR-LPBK-T1 The OPR-LPBK-T1command places a specific T1 facility in loopback mode. Response Forma

15. Test Commands4200-A2-GB20-00 August 200215-3Error Response: sid yy-mm-dd hh:mm:ssM c DENY /* OPR-LPBK-T1:[tid]:aid_ds1:[ctag]::,,,[lpbktype

15. Test Commands15-4 August 2002 4200-A2-GB20-00OPR-LPBK-VCL The OPR-LPBK-VCL command places a specific Virtual Channel Link (VCL) in loopback mo

15. Test Commands4200-A2-GB20-00 August 200215-5Response Format If, in less than 2 seconds, a normal or error response cannot be sent, the following a

15. Test Commands15-6 August 2002 4200-A2-GB20-00Example Place rack 2, shelf 3, slot 5, circuit 1, virtual path LTVCL-7, virtual channel 99 in loopb

15. Test Commands4200-A2-GB20-00 August 200215-7RLS-LPBK-T1 The RLS-LPBK-T1 command releases any loopback currently active at the near end of a spec

15. Test Commands15-8 August 2002 4200-A2-GB20-00Example Release the NTT1 circuit 1 from payload loopback mode. RLS-LPBK-T1:TAMPA:NTT1-1:40; TAMPA

15. Test Commands4200-A2-GB20-00 August 200215-9RLS-LPBK-VCL The RLS-LPBK-VCL command releases any loopback currently active on the selected ATM VCL.

15. Test Commands15-10 August 2002 4200-A2-GB20-00Example Release rack 2, shelf 3, slot 5, circuit 1, virtual path LTVCL-7, virtual channel 99 from

15. Test Commands4200-A2-GB20-00 August 200215-11STA-LAMPTST The STA-LAMPTST command starts a lamp (LED) test on the NE. Response Format If, in less t

2. Using the Command Line Interface4200-A2-GB20-00 August 20022-5Command query. You can obtain help with CLI commands by typing a ? (question mark). A

15. Test Commands15-12 August 2002 4200-A2-GB20-00Example Start a lamp test on the TAMPA device. STA-LAMPTST:TAMPA:COM; TAMPA 01-11-24 12:30:43M

15. Test Commands4200-A2-GB20-00 August 200215-13STP-LAMPTST The STP-LAMPTST command stops a lamp (LED) test on a device. Response Format If, in less

15. Test Commands15-14 August 2002 4200-A2-GB20-00Example Stop a lamp test on the TAMPA device. STP-LAMPTST:TAMPA:COM; TAMPA 01-11-24 12:30:43M 4

4200-A2-GB20-00 August 2002A-1AError CodesOverviewAn error code is 4-character code that can appear in the response of an input command describing why

A. Error CodesA-2 August 2002 4200-A2-GB20-00SROF S Requested operation failedSSRE S System resources exceededSSTP S Command execution stoppedTable

4200-A2-GB20-00 August 2002B-1BCommand Cross ReferenceOverviewThis appendix lists all commands in alphabetical order for easy reference.ACT Commands o

B. Command Cross ReferenceB-2 August 2002 4200-A2-GB20-00ACT CommandsActivate (ACT) commands activate a network element or a user.ALW CommandsAllow

B. Command Cross Reference4200-A2-GB20-00 August 2002B-3DLT CommandsDelete (DLT) commands remove or unassign.ED CommandsEdit (ED) commands change conf

B. Command Cross ReferenceB-4 August 2002 4200-A2-GB20-00ENT CommandsEnter (ENT) commands add new data records. ED-PROFILE-ADSLDNALM ED-PROFILE-ADSL

B. Command Cross Reference4200-A2-GB20-00 August 2002B-5INH CommandsInhibit (INH) commands disable an automatic operation. INIT CommandsInitialize (IN

2. Using the Command Line Interface2-6 August 2002 4200-A2-GB20-00GranDSLAM 4200 Turn-up ProcedureYou can turn up your GranDSLAM 4200 through the Et

B. Command Cross ReferenceB-6 August 2002 4200-A2-GB20-00RD CommandsRead (RD) commands retrieve data from the NE. REPT CommandsReport (REPT) command

B. Command Cross Reference4200-A2-GB20-00 August 2002B-7RTRV CommandsRetrieve (RTRV) commands retrieve data from the NE. Table B-14. RTRV Commands (1

B. Command Cross ReferenceB-8 August 2002 4200-A2-GB20-00RTRV-HDR RTRV-HDR on page 14-15 in Chapter 14, System Commands RTRV-INV-EQPT RTRV-INV-EQPT

B. Command Cross Reference4200-A2-GB20-00 August 2002B-9SET Commands Set (SET) commands modify data related to the system.STA Commands Start (STA) com

B. Command Cross ReferenceB-10 August 2002 4200-A2-GB20-00

4200-A2-GB20-00 August 2002C-1CTraps and MIBsSNMP OverviewThe Simple Network Management Protocol (SNMP) is an application-level protocol used in netwo

C. Traps and MIBsC-2 August 2002 4200-A2-GB20-00SNMP TrapsTable C-1, SNMP Traps, lists the traps supported by the GranDSLAM 4200. Table C-1. SNMP Tr

C. Traps and MIBs4200-A2-GB20-00 August 2002C-3Enterprise-Specific Traps (continued)pdnAtmIfConfExtVclNoBandwidthAvail(4)Traffic contracts associated

C. Traps and MIBsC-4 August 2002 4200-A2-GB20-00ADSL ATU-C DMT Traps (continued)adslAtucSesLThreshTrap Severely errored seconds 15-minute threshold

C. Traps and MIBs4200-A2-GB20-00 August 2002C-5MIBs OverviewThe GranDSLAM 4200 DSL system supports standard as well as Paradyne Enterprise MIBs. Vario

2. Using the Command Line Interface4200-A2-GB20-00 August 20022-7Turn-up Procedure for Inband ManagementProcedureTo turn up the GranDSLAM 4200 using i

C. Traps and MIBsC-6 August 2002 4200-A2-GB20-00ATM Forum MIB — SNMP M4 Network Element View MIB (atmfM4.mib) and atmfM4Ext.mibEntity MIB (version 2

C. Traps and MIBs4200-A2-GB20-00 August 2002C-7MIB II (RFC 1213) The objects defined by MIB II (RFC 1213) are organized into the following groups:Syst

C. Traps and MIBsC-8 August 2002 4200-A2-GB20-00MIB II (RFC 2863)The objects defined by MIB II (RFC 2863) are organized into the following groups:In

C. Traps and MIBs4200-A2-GB20-00 August 2002C-9Table C-3. Interfaces Group Objects (1 of 3)Object Description Setting/ContentsifNumber(interfaces 1)S

C. Traps and MIBsC-10 August 2002 4200-A2-GB20-00ifAdminStatus(ifEntry 7) Specifies the desired state (configuration) of the interface.Upon initiali

C. Traps and MIBs4200-A2-GB20-00 August 2002C-11 ifInErrors (ifEntry 14)DSL1−24 interface: 0ATM1−24 interface: The number of cells dropped due to u

C. Traps and MIBsC-12 August 2002 4200-A2-GB20-00MIB II (RFC 2863) Extension to the Interface TableThis extension contains additional objects for th

C. Traps and MIBs4200-A2-GB20-00 August 2002C-13MIB II (RFC 2863) Interface Test Table For GranDSLAM 4200, the Interface Test Table is supported for i

C. Traps and MIBsC-14 August 2002 4200-A2-GB20-00ATM Interface Configuration Parameter Group (RFC 2515)This group contains information on ATM cell l

C. Traps and MIBs4200-A2-GB20-00 August 2002C-15ATM Interface Traffic Descriptor Group (RFC 2515)The ATM virtual link tables use this ATM Traffic Desc

2. Using the Command Line Interface2-8 August 2002 4200-A2-GB20-005. Enable security for your GranDSLAM 4200 unit. Using the TL1 command ENT-USER-SE

C. Traps and MIBsC-16 August 2002 4200-A2-GB20-00ATM VCL Configuration Group (RFC 2515)Contains configuration and state information of a bidirection

C. Traps and MIBs4200-A2-GB20-00 August 2002C-17Virtual Channel Cross Connect Group (RFC 2515)This table contains configuration and state information

C. Traps and MIBsC-18 August 2002 4200-A2-GB20-00ATM Forum MIBThe ATM Forum MIB (atmfM4.MIB) is defined in the ATM Forum SNMP M4 Network Element Vie

C. Traps and MIBs4200-A2-GB20-00 August 2002C-19Paradyne Extensions to the ATM Interface Configuration Table, ATM Forum M4The following MIBs listed in

C. Traps and MIBsC-20 August 2002 4200-A2-GB20-00Entity MIB (version 2) (RFC 2737)The Entity MIB contains the following five groups of MIB objects:e

C. Traps and MIBs4200-A2-GB20-00 August 2002C-21entPhysicalDescr (entPhysicalEntry 2)(continued)Led PLD: ATM Stackable 4200 DSLAM; Led PLD.; Unit #T1/

C. Traps and MIBsC-22 August 2002 4200-A2-GB20-00entPhysicalContainedIn (entPhysicalEntry 4)(continued)ReachDSL port: entPhysicalIndex for the corre

C. Traps and MIBs4200-A2-GB20-00 August 2002C-23entPhysicalParentRelPos(entPhysicalEntry 6)Identifies the relative position of this child component am

C. Traps and MIBsC-24 August 2002 4200-A2-GB20-00entPhysicalHardwareRev(entPhysicalEntry 8)(continued)Uplink module: string containing the revision

C. Traps and MIBs4200-A2-GB20-00 August 2002C-25entPhysicalSerialNum(entPhysicalEntry 11)Identifies the vendor-specific serial number string for the p

2. Using the Command Line Interface4200-A2-GB20-00 August 20022-9Add to the list of equipped units in the networkENT-EQPT:[tid]:aid_eqpt:[ctag]::eqpt_

C. Traps and MIBsC-26 August 2002 4200-A2-GB20-00entPhysicalAlias (entPhysicalEntry 14)Identifies the alias name of the physical entity as specified

C. Traps and MIBs4200-A2-GB20-00 August 2002C-27DMT Line Code Specific MIB (RFC 2662)The objects supported for the DMT Line Code Specific MIB are list

C. Traps and MIBsC-28 August 2002 4200-A2-GB20-00adslAtucPerfDataEntry adslAtucPerfLofs(1)adslAtucPerfLoss(2)adslAtucPerfLols(3)adslAtucPerfESs(5)ad

C. Traps and MIBs4200-A2-GB20-00 August 2002C-29adslAturPerfDataEntry(continued)adslAturPerfCurr1DayESs(21)adslAturPerfPrev1DayMonisecs(23)adslAturPer

C. Traps and MIBsC-30 August 2002 4200-A2-GB20-00adslAtucChanPerfDataEntry(continued)adslAtucChanPerfCurr1DayUncorrectBlks(16)adslAtucChanPerfPrev1D

C. Traps and MIBs4200-A2-GB20-00 August 2002C-31adslAturChanIntervalEntry adslAturChanIntervalNumber(1)adslAturChanIntervalReceivedBlks(2)adslAturChan

C. Traps and MIBsC-32 August 2002 4200-A2-GB20-00ADSL Supplement to the ADSL Line MIBThe objects supported for the supplement to the ADSL Line MIB a

C. Traps and MIBs4200-A2-GB20-00 August 2002C-33DS1 MIB (RFC 2495)The objects supported for the DS1 MIB are listed in Table C-14, DS1 MIB Objects.Tabl

C. Traps and MIBsC-34 August 2002 4200-A2-GB20-00dsx1IntervalEntry dsx1IntervalIndexdsx1IntervalNumberdsx1IntervalESsdsx1IntervalSESsdsx1IntervalSEF

C. Traps and MIBs4200-A2-GB20-00 August 2002C-35dsx1FarEndCurrentEntry(continued)dsx1FarEndCurrentBESsdsx1FarEndCurrentDMsdsx1FarEndCurrentLCVsPerf Cu

2. Using the Command Line Interface2-10 August 2002 4200-A2-GB20-00

C. Traps and MIBsC-36 August 2002 4200-A2-GB20-00Paradyne Enterprise MIBsThe following Paradyne Enterprise MIB Objects are supported:Paradyne DSLAM

C. Traps and MIBs4200-A2-GB20-00 August 2002C-37loginUserPriv Contains the access privileges of the user.Read only. Valid values are:administrator(1)o

C. Traps and MIBsC-38 August 2002 4200-A2-GB20-00Paradyne Security MIB (pdn_Security.mib)The Paradyne Security MIB (pdn_Security.mib) enables an SNM

C. Traps and MIBs4200-A2-GB20-00 August 2002C-39Paradyne Syslog MIB (pdn_syslog.mib)The Paradyne Syslog MIB (pdn_syslog.mib) defines a set of objects

C. Traps and MIBsC-40 August 2002 4200-A2-GB20-00pdnSyslogSeverityThreshold Specifies the minimum severity level that syslog messages can be sent. V

C. Traps and MIBs4200-A2-GB20-00 August 2002C-41Paradyne Health and Status MIB (mpe_HealthAndStatus.mib)The Paradyne Health and Status MIB (mpe_Health

C. Traps and MIBsC-42 August 2002 4200-A2-GB20-00Paradyne Control MIB (pdn_Control.mib)The Paradyne Control MIB (pdn_Control.mib) stores the results

C. Traps and MIBs4200-A2-GB20-00 August 2002C-43Paradyne Configuration MIB (mpe_Config.mib)The Paradyne Configuration MIB (mpe_Config.mib) allows the

C. Traps and MIBsC-44 August 2002 4200-A2-GB20-00Paradyne Time MIB (pdn_Time.mib)The Paradyne Time MIB (pdn_Time.mib) controls the date and time on

C. Traps and MIBs4200-A2-GB20-00 August 2002C-45Paradyne ReachDSL MIB (pdn_reachDSL.mib)This Paradyne enterprise MIB provides objects for configuratio

4200-A2-GB20-00 August 20023-13ADSL Facility CommandsOverviewThis chapter contains the following ADSL Facility commands:ACT-PROFILE-ADSL on page 3-2AC

C. Traps and MIBsC-46 August 2002 4200-A2-GB20-00Paradyne DS1 Config MIB (RFC 2495)The objects supported for the DS1 MIB are listed in Table C-26, D

4200-A2-GB20-00 August 2002D-1DHotwire 6390 ReachDSL Modem DownloadHotwire 6390 ReachDSL Modem OverviewThe Hotwire 6390 ReachDSL Modem is a component

D. Hotwire 6390 ReachDSL Modem DownloadD-2 August 2002 4200-A2-GB20-00Downloading Hotwire 6390 ReachDSL Modem SoftwareThe Hotwire 6390 ReachDSL Mode

D. Hotwire 6390 ReachDSL Modem Download4200-A2-GB20-00 August 2002D-3ProcedureTo create a PVC from the GrandDSLAM 4200 port to the Hotwire 6390 ReachD

D. Hotwire 6390 ReachDSL Modem DownloadD-4 August 2002 4200-A2-GB20-00ProcedureTo download new software to the Hotwire 6390 ReachDSL Modem flash mem

4200-A2-GB20-00 August 2002IN-1IndexAACTPROFILE-ADSL, 3-2PROFILE-ADSLALM, 3-4USER, 14-2ACT commands, B-2activateADSL alarm profile, 3-4ADSL profi

IndexIN-2August 2002 4200-A2-GB20-00automaticcommand completion, 2-4completion of optional fields, 2-4autonomous messagesallow, 14-4inhibit, 14-9C

Index4200-A2-GB20-00 August 2002IN-3DLTATMARPENT, 8-2CRS-VC, 6-2IPPORT, 8-4PROFILE-ADSL, 3-6PROFILE-ADSLALM, 3-8PROFILE-TRAFDSC, 5-2USER-SECU,

IndexIN-4August 2002 4200-A2-GB20-00ENT-PROFILEADSL, 3-24ADSLALM, 3-26TRAFDSC, 5-8ENT-USER-SECU, 12-10EQPTedit, 7-2report alarm, 7-4report event

Index4200-A2-GB20-00 August 2002IN-5modeDHCP, 2-6manual, 2-6monitoring, A-1Nnetwork diagram, 1-2Network Management System (NMS), C-1OOPRLPBK-T1,

3. ADSL Facility Commands3-2 August 2002 4200-A2-GB20-00ACT-PROFILE-ADSL The ACT-PROFILE-ADSL command activates newly created ADSL profiles. See ENT

IndexIN-6August 2002 4200-A2-GB20-00REPT ALMADSL, 3-28EQPT, 7-4T1, 4-8REPT commands, B-6REPT EVTADSL, 3-30EQPT, 7-5T1, 4-9REPT-OPSTATADSLCOM,

Index4200-A2-GB20-00 August 2002IN-7RTRV-ALM-ALL, 10-5RTRV-ALM-EQPT, 10-9RTRV-ALM-T1, 10-12RTRV-ATMPORT, 5-13RTRV-ATTR-ADSL, 10-15RTRV-ATTR-ALL,

IndexIN-8August 2002 4200-A2-GB20-00turn-up procedureinband management, 2-7out-of-band management, 2-7UUAP, 12-10useraccess privilege, 12-10activa

3. ADSL Facility Commands4200-A2-GB20-00 August 20023-3Example Activate profile 6. ACT-PROFILE-ADSL:TAMPA:6:42; TAMPA 01-11-24 12:30:43M 42 COMPLD

Contentsii August 2002 4200-A2-GB20-00ACT-PROFILE-ADSLALM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4Response Format . .

3. ADSL Facility Commands3-4 August 2002 4200-A2-GB20-00ACT-PROFILE-ADSLALM The ACT-PROFILE-ADSLALM command activates newly created ADSL alarm profi

3. ADSL Facility Commands4200-A2-GB20-00 August 20023-5Example Activate profile 6. ACT-PROFILE-ADSLALM:TAMPA:6:42; TAMPA 01-11-24 12:30:43M 42 COMP

3. ADSL Facility Commands3-6 August 2002 4200-A2-GB20-00DLT-PROFILE-ADSL The DLT-PROFILE-ADSL command deletes selected ADSL modem configuration pro

3. ADSL Facility Commands4200-A2-GB20-00 August 20023-7Example Delete profile 6. DLT-PROFILE-ADSL:TAMPA:6:42;TAMPA 02-01-24 12:30:43M 42 COMPLD /*

3. ADSL Facility Commands3-8 August 2002 4200-A2-GB20-00DLT-PROFILE-ADSLALM The DLT-PROFILE-ADSLALM command deletes selected ADSL alarm configurat

3. ADSL Facility Commands4200-A2-GB20-00 August 20023-9Example Delete profile 6. DLT-PROFILE-ADSLALM:TAMPA:6:42;TAMPA 02-01-24 12:30:43M 42 COMPLD

3. ADSL Facility Commands3-10 August 2002 4200-A2-GB20-00ED-ADSL The ED-ADSL command edits configuration data associated with an ADSL facility on

3. ADSL Facility Commands4200-A2-GB20-00 August 20023-11adsl_nblk (continued)MXTXPWRDN: Specifies the maximum transmission power settings for the ATU-

3. ADSL Facility Commands3-12 August 2002 4200-A2-GB20-00Response Format If, in less than 2 seconds, a normal or error response cannot be sent, the

3. ADSL Facility Commands4200-A2-GB20-00 August 20023-13Example Edit rack 1, shelf 1, slot 1, circuit 20 to have an ADSL line profile of 4 and be in s

Contents4200-A2-GB20-00 August 2002iiiREPT ALM ADSL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-28REPT EVT ADSL

3. ADSL Facility Commands3-14 August 2002 4200-A2-GB20-00ED-PROFILE-ADSLDN The ED-PROFILE-ADSLDN command enables you to edit ADSL line configurat

3. ADSL Facility Commands4200-A2-GB20-00 August 20023-15Error Response: sid yy-mm-dd hh:mm:ssM c DENY /* ED-PROFILE-ADSLDN:[tid]:adsl_profile_i

3. ADSL Facility Commands3-16 August 2002 4200-A2-GB20-00ED-PROFILE-ADSLDNALM The ED-PROFILE-ADSLDNALM command enables you to edit ADSL alarm line

3. ADSL Facility Commands4200-A2-GB20-00 August 20023-17Response Format If, in less than 2 seconds, a normal or error response cannot be sent, the fol

3. ADSL Facility Commands3-18 August 2002 4200-A2-GB20-00Related Commands ENT-PROFILE-ADSLALM on page 3-26RTRV-PROFILE-ADSLDNALM on page 3-47

3. ADSL Facility Commands4200-A2-GB20-00 August 20023-19ED-PROFILE-ADSLUP The ED-PROFILE-ADSLUP command enables you to edit ADSL line configuration

3. ADSL Facility Commands3-20 August 2002 4200-A2-GB20-00Error Response: sid yy-mm-dd hh:mm:ssM c DENY /* ED-PROFILE-ADSLUP:[tid]:adsl_profil

3. ADSL Facility Commands4200-A2-GB20-00 August 20023-21ED-PROFILE-ADSLUPALM The ED-PROFILE-ADSLUPALM command enables you to edit ADSL alarm line co

3. ADSL Facility Commands3-22 August 2002 4200-A2-GB20-00Response Format If, in less than 2 seconds, a normal or error response cannot be sent, the

3. ADSL Facility Commands4200-A2-GB20-00 August 20023-23Example Edit profile 6 to have an Severely Errored Seconds threshold of 8. ED-PROFILE-ADSLUPAL

Contentsiv August 2002 4200-A2-GB20-004 DS1 Facility CommandsOverview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3. ADSL Facility Commands3-24 August 2002 4200-A2-GB20-00ENT-PROFILE-ADSL The ENT-PROFILE-ADSL command allocates a new ADSL line configuration pr

3. ADSL Facility Commands4200-A2-GB20-00 August 20023-25Error Response: sid yy-mm-dd hh:mm:ssM c DENY /* ENT-PROFILE-ADSL:[tid]:adsl_profile_id

3. ADSL Facility Commands3-26 August 2002 4200-A2-GB20-00ENT-PROFILE-ADSLALM The ENT-PROFILE-ADSLALM command allocates a new ADSL alarm configurat

3. ADSL Facility Commands4200-A2-GB20-00 August 20023-27Error Response: sid yy-mm-dd hh:mm:ssM c DENY /* ENT-PROFILE-ADSLALM:[tid]:[adsl_profil

3. ADSL Facility Commands3-28 August 2002 4200-A2-GB20-00REPT ALM ADSL The REPT ALM ADSL message reports current alarms associated with an ADSL fa

3. ADSL Facility Commands4200-A2-GB20-00 August 20023-29[locn] Location of the condition. Valid values are: NEND: Near end FEND: Far end If no value i

3. ADSL Facility Commands3-30 August 2002 4200-A2-GB20-00REPT EVT ADSL The REPT EVT ADSL message reports current events associated with an ADSL fac

3. ADSL Facility Commands4200-A2-GB20-00 August 20023-31ocrtm Time of occurrence in the format hh-mm.[locn] Location of the condition. Valid values ar

3. ADSL Facility Commands3-32 August 2002 4200-A2-GB20-00RTRV-ADSL The RTRV-ADSL command retrieves operational parameters configured for ADSL line

3. ADSL Facility Commands4200-A2-GB20-00 August 20023-33Error Response: sid yy-mm-dd hh:mm:ssM c DENY /* RTRV-ADSL:[tid]:aid_adsl:[ctag]::::[ps

Contents4200-A2-GB20-00 August 2002vENT-PROFILE-TRAFDSC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-8Response Format . . .

3. ADSL Facility Commands3-34 August 2002 4200-A2-GB20-00Example Retrieve ADSL configuration for data rack 1, shelf 1, slot 1, circuit 9. RTRV-ADSL:

3. ADSL Facility Commands4200-A2-GB20-00 August 20023-35RTRV-ATUR The RTRV-ATUR command retrieves operational parameters configured for the ADSL ATU-

3. ADSL Facility Commands3-36 August 2002 4200-A2-GB20-00Example Retrieve ATU-R configuration data for rack 1, shelf 1, slot 1, circuit 9. RTRV-ATUR

3. ADSL Facility Commands4200-A2-GB20-00 August 20023-37RTRV-PM-ADSL The RTRV-PM-ADSL command retrieves performance monitoring data for selected ADSL

3. ADSL Facility Commands3-38 August 2002 4200-A2-GB20-00Response Format If, in less than 2 seconds, a normal or error response cannot be sent, the

3. ADSL Facility Commands4200-A2-GB20-00 August 20023-39Example Retrieve the near-end errored seconds (fast channel) count above 5187 on ADSL rack 1,

3. ADSL Facility Commands3-40 August 2002 4200-A2-GB20-00RTRV-PROFILE-ADSL The RTRV-PROFILE-ADSL command retrieves information about ADSL line conf

3. ADSL Facility Commands4200-A2-GB20-00 August 20023-41Example Retrieve profile 5. RTRV-PROFILE-ADSL:TAMPA:5:42; TAMPA 02-07-24 12:30:43M 42 COMPL

3. ADSL Facility Commands3-42 August 2002 4200-A2-GB20-00RTRV-PROFILE-ADSLALM The RTRV-PROFILE-ADSLALM command retrieves information about ADSL ala

3. ADSL Facility Commands4200-A2-GB20-00 August 20023-43Example Retrieve alarm profile 5. RTRV-PROFILE-ADSLALM:TAMPA:5:42; TAMPA 02-07-24 12:30:43M

Contentsvi August 2002 4200-A2-GB20-00ENT-CRS-VC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7Response Fo

3. ADSL Facility Commands3-44 August 2002 4200-A2-GB20-00RTRV-PROFILE-ADSLDN The RTRV-PROFILE-ADSLDN command enables you to retrieve ADSL line confi

3. ADSL Facility Commands4200-A2-GB20-00 August 20023-45Table 3-36. RTRV-PROFILE-ADSLDN Response ParametersParameter Explanation tid Target NE identif

3. ADSL Facility Commands3-46 August 2002 4200-A2-GB20-00Example Retrieve profile 6. RTRV-PROFILE-ADSLDN:TAMPA:6:42; TAMPA 02-07-24 12:30:43M 42

3. ADSL Facility Commands4200-A2-GB20-00 August 20023-47RTRV-PROFILE-ADSLDNALM The RTRV-PROFILE-ADSLDNALM command enables you to retrieve ADSL alarm c

3. ADSL Facility Commands3-48 August 2002 4200-A2-GB20-00Table 3-38. RTRV-PROFILE-ADSLDNALM Response Parameters (1 of 2)Parameter Explanation tid Ta

3. ADSL Facility Commands4200-A2-GB20-00 August 20023-49Example Retrieve profile 6. RTRV-PROFILE-ADSLDNALM:TAMPA:6:42; TAMPA 02-07-24 12:30:43M 42

3. ADSL Facility Commands3-50 August 2002 4200-A2-GB20-00RTRV-PROFILE-ADSLUP The RTRV-PROFILE-ADSLUP command enables you to retrieve ADSL line confi

3. ADSL Facility Commands4200-A2-GB20-00 August 20023-51Table 3-40. RTRV-PROFILE-ADSLUP Response ParametersParameter Explanation tid Target NE identif

3. ADSL Facility Commands3-52 August 2002 4200-A2-GB20-00Example Retrieve profile 6. RTRV-PROFILE-ADSLUP:TAMPA:6:42; TAMPA 02-07-24 12:30:43M 42

3. ADSL Facility Commands4200-A2-GB20-00 August 20023-53RTRV-PROFILE-ADSLUPALM The RTRV-PROFILE-ADSLUPALM command enables you to retrieve ADSL alarm c

Contents4200-A2-GB20-00 August 2002viiED-IPPORT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-6Response

3. ADSL Facility Commands3-54 August 2002 4200-A2-GB20-00Table 3-42. RTRV-PROFILE-ADSLUPALM Response Parameters (1 of 2)Parameter Explanation tid Ta

3. ADSL Facility Commands4200-A2-GB20-00 August 20023-55Example Retrieve profile 6. RTRV-PROFILE-ADSLUPALM:TAMPA:6:42; TAMPA 02-07-24 12:30:43M 42

3. ADSL Facility Commands3-56 August 2002 4200-A2-GB20-00

4200-A2-GB20-00 August 20024-14DS1 Facility CommandsOverviewThis chapter contains the following DS1 Facility commands:ED-T1 on page 4-2ENT-T1 on page

4. DS1 Facility Commands4-2 August 2002 4200-A2-GB20-00ED-T1 The ED-T1 Command edits configuration data associated with a DS1 facility. Table 4-1

4. DS1 Facility Commands4200-A2-GB20-00 August 20024-3Response Format If, in less than 2 seconds, a normal or error response cannot be sent, the follo

4. DS1 Facility Commands4-4 August 2002 4200-A2-GB20-00Example Edit circuit 1 on the NT to have a line interface type of T1. ED-T1:TAMPA:NTT1-1:42::

4. DS1 Facility Commands4200-A2-GB20-00 August 20024-5ENT-T1 The ENT-T1 command enters or initializes the configuration data associated with a DS-1

4. DS1 Facility Commands4-6 August 2002 4200-A2-GB20-00Response Format If, in less than 2 seconds, a normal or error response cannot be sent, the fo

4. DS1 Facility Commands4200-A2-GB20-00 August 20024-7Error Response sid yy-mm-dd hh:mm:ssM c DENY /* ENT-T1:[tid]:aid_ds1:[ctag]:::ds1_nblk:[p