Paradyne Switch 6800 User Manual Page 196
- Page / 237
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
2Modem/DSU Commands
2-1736800-A2-GB31-20 January 1997
Access module id
The number of ports served by the modem is 1-Port.
Modem Configuration
The modem configuration of the device is DDD, 2-Wire APL, 4-Wire APL, or 4-Wire
APL Multi-point.
Modem Strapping
The modem (international) strapping of the device, North American, Generic, Japan,
UK, Italy, Germany, Belgium, Austarlia, New Zealand, France, Switzerland,
Netherlands, Spain, Austria, Denmark, Sweden, Norway, Finland, Cyprus, Portugal,
Singapore, Malaysia, Turkey.
Hardware Part Number
An alphanumeric, 11-character set that identifies the circuit card in the modem.
Software Part Number
An alphanumeric, 11-character set that identifies the firmware release number.
Installed Features
The features installed on the device, Trellis Multipoint, V.32 bis, V.33, V.29, V.27 bis,
Expanded security database capacity, Proprietary 28.8, Proprietary 1200, or Dual
Leased Line.
The following selections are added to the Installed Features field of this command for 3980,
3981, and 3982 modems.
• V.34
• 2-Wire
The results form now displays 3920 and or 3921 in the Model field in support of 392xPlus
modems.
The following selection is added to the Installed Features field.
• V.34
- COMSPHERE 1
- 6800 SERIES NETWORK 1
- MANAGEMENT SYSTEM 1
- Table of Contents 3
- List of Figures 5
- List of Tables 7
- Related Documents 8
- 1Introduction 10
- NMS-Supported APL Modems 11
- Naming Conventions 12
- Device Addressing 13
- Command Access 13
- Shortcut for Command Access 14
- Wildcard Characters 14
- Multiple Entries 14
- Command Input Forms 17
- Display-only Fields 18
- Carried-over Fields 18
- Results Forms 21
- In Menus 22
- In Forms 22
- For Screen Input Fields 23
- Overview 25
- Abort (abort) 26
- Abort Command Results Form 27
- Automatic Network Test (ant) 30
- Call Detail Display (cded) 34
- Call Fault Criteria (cfc) 43
- Call Fault Read (cfr) 47
- Call Message (cm) 50
- Call Message Results Form 51
- Call Test (ct) 55
- Call Test Results Form 56
- Change Address (cha) 57
- Change Address Results Form 60
- Change Call Directory (chcd) 62
- Change Canned Message (chcm) 67
- Change Directory (chd) 69
- Change Directory Results Form 70
- Change Line Designator (chld) 78
- Change Multiplexer (chm) 79
- Change Options (cho) 81
- Change Options Input Forms 82
- Change Options Results Form 82
- Change Port Options (chpo) 86
- Change Port Speed(s) (chpsp) 88
- Change Protocol Mode (chpm) 91
- Change Thresholds (cht) 97
- (Required field) 99
- 2Modem/DSU Commands 100
- Circuit Loss Inbound (cli) 101
- (Disruptive) 101
- Circuit Loss Outbound (clo) 103
- Circuit Quality (cq) 105
- : 1–10 Hz 109
- Clear Call Directory (clcd) 111
- Page 1 for Single Devices 121
- Page 1 for Subnetwork Devices 123
- Device Test (det) 125
- Device Test Results Form 126
- Dial (dial) 127
- Dial Command Input Form 128
- Dial Command Results Form 130
- Dial Mode (dm) 131
- Dial Standby (ds) 132
- 132
- Digital Test (dit) 133
- Digital Test Results Form 135
- Disable/Enable (de) 139
- Disable/Enable Results Form 140
- Display Address (dsa) 141
- Display Call Directory (dscd) 145
- Display Canned Message (dscm) 148
- Display Options (dso) 156
- Display Port Options (dspo) 159
- Display Port Speed(s) (dspsp) 161
- Display Thresholds (dst) 165
- EIA Status (eias) 173
- End-to-End Test (eet) 179
- End-To-End Test Results Form 181
- Exception Reports (er) 182
- Exception Reports Input Form 183
- Identity (id) 188
- Page 1 for 3600 Series DSUs 191
- Page 1 for 3900 Series Modems 195
- List Directory (lsd) 197
- List Directory Results Form 198
- Loopback (lo) 199
- Loopback Test Results Form 201
- Make Busy (mkb) 202
- Manage Call Statistics (mcs) 203
- Offline Test (ot) 209
- Receive Signal Level (rsl) 210
- Receive Signal Quality (rsq) 211
- Report Terminal Power (rtp) 216
- Reset (reset) 217
- Send Message (snm) 218
- Send Tone (snt) 219
- Send Tone Results Form 220
- Service Line (sl) 221
- Signal Profile (sp) 222
- Standby Facility (sf) 226
- Standby Facility Results Form 227
- Training Time (tt) 228
- Training Time Results Form 229
- Transmit Test Pattern (ttp) 230
- Trending Reports (tr) 232
- Trending Reports Input Form 233
- Phase jitter 234
- Trending Reports Results Form 235
© 2020, manymanuals.com. All rights reserved. | 2.524 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals