Paradyne 12-Port User Manual download pdf

210-0000025 rev04

TAM1500-12

12-Port T1 Access Multiplexer

INSTALLATION

1. Unpack and inspect the TAM1500-12.

If there is visible damage, do not attempt to connect the device; contact Customer Support at 1-

877-638-2638 (001-603-427-0600 for international customers) or Support@NetToNet.com.

2. Install the TAM1500-12 in an IP DSLAM chassis.

All Access Multiplexer Modules for Net to Net Technologies' IP DSLAMs are hot swappable;

installing or removing an Access Module while the chassis is powered up does not affect the

operational status of other Access Modules within the chassis. The IPD12000 is a fourteen slot

chassis; slots 1-12 are reserved for Access Modules (such as the TAM1500-12) and slots 13-14

are reserved for Multiplexer Uplink Modules (such as the MUM200-2). Access Modules may be

placed in any order in slots 1-12. The IPD4000 is a five slot chassis; slots 1-4 are reserved for

Access Modules and slot 5 is reserved for a Multiplexer Uplink Module.

a. Align the TAM1500-12 with the slot module guides of the chosen slot for installation (slot

1-12 on the IPD12000 or slot 1-4 on the IPD4000).

b. Slide the TAM1500-12 firmly into the chassis. DO NOT USE EXCESS FORCE.

c. Secure the TAM1500-12 by tightening the fastening screws on the module faceplate.

d. Verify that the PWR (Power) LED on the TAM1500-12 faceplate is illuminated.

Interface Module User Guide

CAUTION

Net to Net Technologies strongly recommends the use of proper electrostatic discharge (ESD) precautions

when handling this equipment.

NOTE

There must be a Multiplexer Uplink Module installed in the IP DSLAM chassis in order for Access Modules to

operate.

1 2 3 4 5 6 7 8

Summary of Contents

Page 1 - TAM1500-12

210-0000025 rev04TAM1500-1212-Port T1 Access MultiplexerINSTALLATION1. Unpack and inspect the TAM1500-12.If there is visible damage, do not attempt to

Page 2 - OVERVIEW

210-0000025 rev043. Connect the T1 Line(s).Plug the T1 cable into the RJ21 connector for the chosen slot on the back of the IP DSLAM. The TAM1500-12 w

Page 3 - Default Settings

210-0000025 rev04!192.168.254.252 if the MUM is in slot 13 (IPD12000) or slot 5 (IPD4000) !192.168.254.253 if the MUM is in slot 14 (IPD12000) e. Log

Page 4 - Data Storage

210-0000025 rev04Management System Configuration DefaultsTAM1500-12 Circuit DefaultsData StorageConfiguration backup is inherent in the TAM1500-12. Up

Page 5 - Tx (Transmit) Buildout

210-0000025 rev04Frame TypeFrame type is the T1 data encapsulation method. A frame consists of 193 bits (8-bit samples of each of the 24 T1 channels p

Page 6 - ADDITIONAL INFORMATION

210-0000025 rev040db (Default)Receivers on most newer T1 equipment (repeaters, switches, etc.) can automatically adjust for incoming amplitude, allowi

Page 7 - 210-0000025 rev04

210-0000025 rev04(A pulsing LED blinks steadily at a rate of once per second. A flashing LED blinks at a more rapid, less constant rate.)Regulatory Co

Page 8

210-0000025 rev04Caution: This unit does not contain any user serviceable parts. Repair service and/or warranty information may be obtained by contact

Comments to this Manuals

No comments

Paradyne 12-Port User Manual

Browse online or download User Manual for Bridges & repeaters Paradyne 12-Port. Paradyne 12-Port User's Manual

Summary of Contents

Comments to this Manuals